Purchase Registration Form for seat covers with Standard Integrated Side Airbags
This purchase registration records your side integrated airbag compatible seat covers. Your registration will be saved together with the production information of your individual seat covers. This data will be treated with the strictest confidence.
1. Safety Information
Correct initial fitting and securing of this seat cover on the vehicle is essential to guarantee the safety of the user. Incorrect fitting can prevent the seat airbag from inflating correctly in the event of a collision. When fitting the seat cover proceed as follows:
a) Seat covers have universal side opening seams on both left and right hand side of the seat cover to permit fitting on either driver or passenger seats.
b) Driver and passenger seat covers must be fitted in the correct position, with the side seam of the cover placed over the side “Airbag” of the car seats.
c) Driver and passenger seats must be mounted in the correct positions. These can be determined by the “Airbag” markings on the seat cover. (See figure 1.0)
d) Seat covers that have slipped must be repositioned. If this is no longer possible because of advanced wear the cover must be removed and replaced.
e) Do not tamper with the opening side seam of the seat cover.
f) Regularly inspect seat covers for wear, damage and seat cover misalignment.
g) Adjust alignment if seat cover twists or moves from its original central aligned position.
h) If the side seam splits for any reason it CANNOT be repaired. Any attempt to re sew the seam may interfere with the Standard Integrated Side Airbag Deployment.
i) Discard seat cover after side airbag activation.
j) Airbag deployment must never be compromised by the incorrect fitting of car set covers.
k) Observe the fitting instructions below.
Fitting Instructions
Step 1
Remove Head Rests where possible, fit the Back Rest section over the seat, ease down and cover until you have a snug fit. Feed buckles through to back of seat.
Step 2
Pull seat cover down over the seat until you have a snug fit.
Step 3
Fasten corresponding side strips, then connect back and front buckle. Secure by tightening and then adjust to fit.
Step 4
Replace Head Rest, attach Head Rest Cover and pull Cover down over Head Rest until you have a snug fit. Secure with velcro.
Care Instructions
Hand wash with approved wool detergents, do not soak for prolonged periods. Rinse and gentle spin (fleece out). Dry naturally at room temperature away from direct heat, preferably flat in shaded area. While still damp gently pull into shape and brush with a course stiff brush to restore pile. Do not iron. Specialist dry-cleaning recommended.
Manufacturer
ILANA ACCESSORIES PTY LTD. Head Office: 20 Hoddle St. Abbotsford VIC 3067 Australia.
ABN 95 894 986 813 • Tel. 03 9419 4228, Fax. 03 9416 0317 • Website: www.carseatcovers.com.au
1. Safety Information
Correct initial fitting and securing of this seat cover on the vehicle is essential to guarantee the safety of the user. Incorrect fitting can prevent the seat airbag from inflating correctly in the event of a collision. When fitting the seat cover proceed as follows:
a) Seat covers have universal side opening seams on both left and right hand side of the seat cover to permit fitting on either driver or passenger seats.
b) Driver and passenger seat covers must be fitted in the correct position, with the side seam of the cover placed over the side “Airbag” of the car seats.
c) Driver and passenger seats must be mounted in the correct positions. These can be determined by the “Airbag” markings on the seat cover. (See figure 1.0)
d) Seat covers that have slipped must be repositioned. If this is no longer possible because of advanced wear the cover must be removed and replaced.
e) Do not tamper with the opening side seam of the seat cover.
f) Deploy Safe
™ seat covers are designed to allow the side seams to split open upon deployment of an airbag because they are constructed using a computer controlled stitching process and a specialised thread.
g) Regularly inspect seat covers for wear, damage and seat cover misalignment.
h) Adjust alignment if seat cover twists or moves from its original central aligned position.
i) If the side seam splits for any reason it CANNOT be repaired. Any attempt to re sew the seam may interfere with the Standard Integrated Side Airbag Deployment.
j) Discard seat cover after side airbag activation.
k) Airbag deployment must never be compromised by the incorrect fitting of car set covers.
l) Observe the fitting instructions below.
2. Fitting Instructions
Step 1
Remove Head Rests where
possible, fit the Back Rest section over the seat, ease down and cover
until you have a snug fit. Feed velcro through to back of seat.
Step
2
Pull seat cover down over the seat until you have a snug fit.
Step
3
Fasten corresponding side strips, then connect back and front
velcro strips. Secure by tightening and then adjust to fit.
Step 4
Replace
Head Rest, attach Head Rest Cover and pull Cover down over Head Rest
until you have a snug fit. Secure with velcro strips.
3. Care Instructions
Wash separately on gentle cold cycle, do not soak, bleach, wring or spin. Do not dry clean, do not iron.
4. Manufacturer
ILANA ACCESSORIES PTY LTD. Head Office: 20 Hoddle St.
Abbotsford VIC 3067 Australia.
ABN 95 894 986 813 • Tel. 03 9419 4228, Fax. 03 9416 0317 • Website:
www.carseatcovers.com.au
1. Safety Information
Correct initial fitting and securing of this seat cover on the vehicle is essential to guarantee the safety of the user. Incorrect fitting can prevent the seat airbag from inflating correctly in the event of a collision. When fitting the seat cover proceed as follows:
a) Seat covers have universal side opening seams on left and right hand side of the seat cover to permit fitting. (See figure 1.0)
b) Ensure that the Airbag opening in the seat covers is on the outside of the seat facing the door. Passenger seat covers must also be fitted the same way.
c) Driver and passenger seat covers must be fitted in the correct position, with the side seam of the cover placed over the side “Airbag” of the car seats.
d) Driver and passenger seats must be mounted in the correct positions. These can be determined by the
“Airbag” markings on the seat cover. (See figure 1.0)
e) Seat covers that have slipped must be repositioned. If this is no longer possible because of advanced wear the cover must be removed and replaced.
f) Do not tamper with the opening side seam of the seat cover.
g) Regularly inspect seat covers for wear, damage and seat cover misalignment.
h) Adjust alignment if seat cover twists or moves from its original central aligned position.
i) If the side seam splits for any reason it CANNOT be repaired. Any attempt to re sew the seam may interfere with the Standard Integrated Side Airbag Deployment.
j) Discard seat cover after side airbag activation.
j) Airbag deployment must never be compromised by the incorrect fitting of car set covers.
k) Observe the fitting instructions below.
2. Fitting Instructions
Step 1
Remove Head Rests where
possible, fit the Back Rest section over the seat, ease down and cover
until you have a snug fit. Feed strips through to back of seat.
Step
2
Pull seat cover down over the seat until you have a snug fit.
Step
3
Fasten corresponding side strips, then connect back and front
strips. Secure by tightening and then adjust to fit.
Step 4
Replace
Head Rest, attach Head Rest Cover and pull Cover down over Head Rest
until you have a snug fit. Secure with strips.
3a. Care Instructions for Fabric
Wash separately on gentle cold cycle, do not soak, bleach, wring or spin. Do not dry clean, do not iron.
3b. Care Instructions for Sheepskin
Hand wash with approved wool detergents, do not soak for prolonged periods. Rinse and gentle spin (fleece out). Dry naturally at room temperature away from direct heat, preferably flat in shaded area.
While still damp gently pull into shape and brush with a course stiff brush to restore pile. Do not iron. Specialist dry-cleaning recommended.
4. Manufacturer
ILANA ACCESSORIES PTY LTD. Head Office: 20 Hoddle St.
Abbotsford VIC 3067 Australia.
ABN 95 894 986 813 • Tel. 03 9419 4228, Fax. 03 9416 0317 • Website:
www.carseatcovers.com.au
1. Safety Information
Correct initial fitting and securing of this seat cover on the vehicle is essential to guarantee the safety of the user. Incorrect fitting can prevent the seat airbag from inflating correctly in the event of a collision. When fitting the seat cover proceed as follows:
a) Seat covers have universal side opening seams on both left and right hand side of the seat cover to permit fitting on either driver or passenger seats.
b) Driver and passenger seat covers must be fitted in the correct position, with the side seam of the cover placed over the side “Airbag” of the car seats.
c) Driver and passenger seats must be mounted in the correct positions. These can be determined by the “Airbag” markings on the seat cover. (See figure 1.0)
d) Seat covers that have slipped must be repositioned. If this is no longer possible because of advanced wear the cover must be removed and replaced.
e) Do not tamper with the opening side seam of the seat cover.
f) Deploy Safe
™ seat covers are designed to allow the side seams to split open upon deployment of an airbag because they are constructed using a computer controlled stitching process and a specialised thread.
g) Regularly inspect seat covers for wear, damage and seat cover misalignment.
h) Adjust alignment if seat cover twists or moves from its original central aligned position.
i) If the side seam splits for any reason it CAN NOT be repaired. Any attempt to re sew the seam may interfere with the Standard Integrated Side Airbag Deployment.
j) Discard seat cover after side airbag activation.
k) Airbag deployment must never be compromised by the incorrect fitting of car set covers.
l) Observe the fitting instructions below.
2. Fitting Instructions
Step 1
Remove Head Rests where
possible, fit the Back Rest section over the seat, ease down and cover
until you have a snug fit. Feed strips through to back of seat.
Step
2
Pull seat cover down over the seat until you have a snug fit.
Step
3
Fasten corresponding side strips, then connect back and front
strips. Secure by tightening and then adjust to fit.
Step 4
Replace
Head Rest, attach Head Rest Cover and pull Cover down over Head Rest
until you have a snug fit. Secure with strips.
3. Care Instructions
Wash separately on gentle cold cycle, do not soak, bleach, wring or spin. Do not dry clean, do not iron.
4. Manufacturer
ILANA ACCESSORIES PTY LTD. Head Office: 20 Hoddle St.
Abbotsford VIC 3067 Australia.
ABN 95 894 986 813 • Tel. 03 9419 4228, Fax. 03 9416 0317 • Website:
www.carseatcovers.com.au